Test Method For Bond Ball Mill Work Index,The standard bond rod mill work index test procedure is firstly to stage crush the feed to pass 127 mm and size a representative test then involves a series of batch grinds in a standard bond rod millA bond rod mill is 0610m with wave liners of a form described by bond which runs at 40rpm and tilts as described below... As a leading global manufacturer of crushing equipment, milling equipment,dressing equipment,drying equipment and briquette equipment etc. we offer advanced, rational solutions for any size-reduction requirements, including quarry, aggregate, grinding production and complete plant plan.
Get PriceFeeding Granularity: ≤20-≤25mm
Applied Materials: Limestone, calcite, barite, dolomite, potassium feldspar, marble, talcum, gypsum, kaolin, bentonite, medical stone, rock phosphate, manganese ore, iron ore, copper ore, gold ore,quartz, active carbon, carbon black, ceramic, coal, etc.
Applicable Range: Cement, silicate product, new building material, refractory material, fertilizer, black and non-ferrous metal ore dressing and glass ceramics production industry, etc.
Outer Cylinder Length: 6-8.5m
Production Capacity: 20-99TPH
Processible Materials: Mineral ores, sand, ore powder, metal powder, gypsum powder, clay, coal slime, coal powder, sawdust, wood, coconut shell, palm shell, etc.
Feeding Size: 120-1500mm
Product Capacity: 1-2200TPH
Application Field: Mining, metallurgy, construction, highway, railroad, and water conservancy, etc.
Feeding Size: 65-300mm
Discharging Size: 3-60mm
Production Capacity: 12-1000t/h
The standard bond rod mill work index test procedure is firstly to stage crush the feed to pass 127 mm and size a representative test then involves a series of batch grinds in a standard bond rod millA bond rod mill is 0610m with wave liners of a form described by bond which runs at 40rpm and tilts as described below
Get PriceThis Grindability Test or Bond Ball Mill Work Index Procedure is used to determine the Bond Work Index of minus six mesh or finer feed ore samples These equation application methods are used to process 12″ ore samples in a Ball Mill using a standard ball charge Below describes in general terms the Bond Work Index Procedure used by a Professional Metallurgical Testing Laboratory If you
Get PriceAbstract The Bond ball mill grindability test is run in a laboratory until a circulating load of 250 is developed It provides the Bond Ball Mill Work Index which expresses the resistance of material to ball milling This happens after 7–10 grinding cycles which shows that the procedure is a lengthy and complex one and is therefore susceptible to procedural errors
Get PriceThe Bond ball mill work index is one of the most commonly used grindability tests in mining and is often referred to as the Bond work index The test is a lockedcycle test where ground product is removed from test cycles and replaced by fresh feed The test much achieve a steadystate before completion Sample Requirements
Get PriceBond Ball Mill Grindability Test The Bond Ball Mill Work Index BBWi test is carried out in a standardised ball mill with a predefined media and ore charge The Work Index calculated from the testing can be used in the design and analysis of ball mill circuits The test requires a minimum of 10kg of sample that has been stagecrushed to 100
Get PriceHere is the old AllisChalmers Bond Work Index Grindability Test Procedure The standard feed is prepared by stage crushing to all passing a 6 mesh sieve but finer feed can be used when necessary It is screen analyzed and packed by shaking in a 1000cc graduated cylinder and the weight of 700 cc is placed in the mill and ground dry at 250 per cent circulating load The mill is 12 in x 12
Get PriceThe Bond Abrasion Test determines the Abrasion Index which is used to determine steel media and liner wear in crushers rod mills and ball mills Bond developed the following correlations based on the wear rate in pounds of metal wearkWh of energy used in the comminution process
Get PriceThe ball mill work index laboratory test is conducted by grinding an ore sample prepared to 100 passing 336 mm 6 mesh to product size in the range of 45150 µm 325100 mesh thus determining the ball mill work index WiB or BWi
Get PriceBond Ball Mill Grindability Test The test determines the Bond Ball Mill Work Index which is used with Bond’s Third Theory of Comminution to calculate net power requirements Various correction factors may have to be applied W Wi 10√P – 10√F Where W Net power consumption in kWht
Get PriceThis knowledge is essential to define the required ball mill layout and production capacity In order to perform the Bond Index Test successfully it is necessary to use precrushed sample material as defined below Module Ball Mill Minerals precrushed to 335 mm and sieved Drillcore precrushed to 335 mm and sieved Half Drillcore pre
Get Price